基于光流法的固体内部声传播方向测量

目前采用光弹设备测量超声传播方向多为人眼主观观测,其误差较大,难以实现精确的定量测量。将Farneback光流法应用于光弹图像的处理,并根据帧与帧之间的光流图来计算光弹图像中的超声传播方向,可以捕捉图像中的动态声场。在实验中对不同传播方向的超声进行了测量,其绝对偏差度数最大值为2.85°,测量结果较为准确。因此,Farneback光流法可用于光弹图像中声波传播方向的判断,且具有快速、准确和直观等特点。     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

气动弹片对垂直轴风力机性能影响研究

片对垂直轴风力机气动性能的影响并分析了其流动机理。结果表明：气动弹片在高尖速比下可显著抑制流动分离并改善其动态失速特性，功率系数得到极大提升；切向力和转矩系数在气动弹片作用相位角范围内，均有一定提高，而在其它相位角内，风力机性能不受影响。     

中压进汽腔的流场数值模拟比较

通过数值模拟计算,对中压对称进汽和切向进汽两种结构的流场进行了分析比较,结果表明,单一切向进汽腔的总压损失更小,出口汽流角的周向分布均匀度更好。更进一步,为整体评估中压进汽腔的流场以及对叶片级的流动影响,对中压进汽腔及第1级叶片的整体流体域流场情况进行了分析比较,结果表明,采用大几何角静叶的切向进汽腔气动性能最优;当采取切向进汽腔时,需合理选择第1级静叶几何角并耦合计算,才能实现进汽腔的气动优化。     

A computational study of unsteady radiative magnetohydrodynamic Blasius and Sakiadis flow with leading‐edge accretion (ablation)

The present study investigates the influence of the magnetic field, thermal radiation, Prandtl number, and leading‐edge accretion/ablation on Blasius and Sakiadis flow. The convective boundary condition is employed to investigate the heat transfer. The nondimensional governing boundary layer equations have been solved by the homotopy analysis method for different values of the pertinent parameters. The effects of these parameters on the dimensionless velocity, temperature, skin friction, and Nusselt number are also investigated for various values of relevant parameters affecting the flow and heat transfer phenomena. The most relevant outcomes of the present study are that enhancement in magnetic field strength undermines the flow velocity establishing thinner velocity boundary layer for both Blasius and Sakiadis flows while an increase in accretion/ablation effect at leading‐edge manifests in a deceleration in velocity for Blasius case and the opposite trend is observed for Sakiadis flow. Another important outcome is that an increase in radiation and accretion/ablation at leading‐edge upsurges the fluid temperature leading to enhancement in the thermal boundary layer. For both Blasius and Sakiadis flow, the skin friction coefficient and the heat transfer rate decline with the enhancement of the leading‐edge accretion parameter. The results are compared with the existing data and are found in good agreement.     

活性焦法烧结烟气脱硫率影响因素统计解析

摘要：为明确影响活性焦烧结烟气脱硫的主要因素，通过模拟试验和生产数据统计分析探究脱硫塔自上至下脱硫率变化趋势和各运行参数对脱硫率的影响。模拟试验表明，循环使用后的活性焦孔隙结构更加发达，表面含氧官能团含量增加，进而其初期脱硫性能低于新鲜活性焦，后期优于新鲜活性焦。错流式脱硫塔自上至下脱硫率先后经历100%、快速降低、缓慢降低等过程。生产数据统计分析表明，脱硫率与SO2质量浓度、O2体积分数、H2O体积分数、NH3与NOx物质的量之比、解析温度呈正相关，与活性焦床温度、体积空速呈负相关。其中，SO2质量浓度、体积空速、活性焦床温度对脱硫率影响最大。运行参数之间存在多重共线性现象，烧结漏风率升高或空气补加量增加将引起诸多运行参数的变化，但总体上有利于脱硫率的提高。     

大涡模拟Smagorinsky模型用于磨粒流精密加工喷嘴的质量控制研究

为研究固液两相磨粒流加工喷嘴小孔过程中的流场分布、涡旋形成规律及涡旋的存在对磨粒流加工的影响机制，采用Smagorinsky亚格子模型对磨粒流加工喷嘴小孔的流道进行大涡数值模拟，并使用磨粒流对变直径喷嘴工件进行加工试验。数值模拟发现磨粒流流体中磨粒与壁面的碰撞与剪切作用随流体的速度增大而增大，同一截面的速度存在速度差，其中还伴随涡旋的存在；通过试验研究发现：经固液两相磨粒流加工后的喷嘴小孔表面质量得到明显提高，喷嘴经过四次不同入口速度的磨粒流加工后大孔处表面粗糙度Ra由1.24 μm降至0.542 μm，小孔处表面粗糙度Ra由1.21 μm降至0.437 μm。结论显示固液两相磨粒流加工技术可有效提高被加工喷嘴工件的内表面质量，加工时同一截面的速度存在速度差，速度差的存在利于涡旋的形成，涡旋的存在利于提高磨粒流加工过程的剪切作用，有助于获得高质量的喷嘴小孔内通道表面。     

The influence of the waveguide on the quality of measurements with ultrasonic Doppler velocimetry

The article is devoted to the study of the influence of geometric parameters of sound-conducting walls on the quality of measurement of liquid metal flow velocities by ultrasonic Doppler velocimetry. It was shown that the thickness and radius of a sound-conducting wall (waveguide) have a notable effect on the resulting velocity profiles. The flow in a round pipe, the length of which is much larger than its diameter, is considered as a reference flow. The positive effect of a stepwise waveguides with a diameter smaller than the diameter of the piezoelectric element of an ultrasonic transducer on the quality of velocity measurements was verified experimentally. It was found that the accuracy of the resulting velocity profiles largely depends on the length and the material of the waveguides, as well as the velocity of the incoming flow of liquid metal.     

水泵水轮机导叶动态水力矩特性分析

采用SST k-ω湍流模型对某高水头水泵水轮机进行全流道三维非定常数值模拟,分别对在水轮机工况和水泵工况运行下的导叶动态力矩特性进行分析。结果表明:在水轮机工况下,随着流量的增大,不同位置处导叶的动态水力矩变化规律一致,力矩值由正值变为负值,力矩脉动频率与转轮叶片数相关,流量越大,叶频影响越显著;在水泵工况下,最高扬程工况时导叶水力矩脉动频率主频为转频且脉动幅值较大,而最低扬程工况下导叶水力矩脉动主频为叶频,力矩脉动幅值较小。